Victron Connect, why Bluetooth configuration can make so much sense

Ben Ellison

Ben Ellison

Panbo editor, publisher & chief bottlewasher from 4/2005 until 8/2018, and now pleased to have Ben Stein as a very able publisher, webmaster, and editing colleague. Please don't regard him as an "expert"; he's getting quite old and thinks that "fadiddling fumble-putz" is a more accurate description.

21 Responses

  1. Steve says:

    Wow, I’d love to read that again in English!!!!

  2. Todd Edger says:

    Yes still eagerly waiting for Bluetooth App for my beta Balmar SG200.

  3. RickG says:

    I run the same solar controllers for our Firefly bank. The bluetooth option is wonderful.

    Question: 16.5V equalization voltage for Fireflys? I see it is disabled, but I set EQ at the float voltage to prevent an accidental battery killing glitch.

    • Ben Ellison Ben Ellison says:

      Thanks, RickG; your suggested change already made with Victron Connect 😉 But I might change it again to 0v as I notice that Victron uses that value for battery presets setup of their Lithium models, which also shouldn’t be equalized.

      I also thought about modifying the temperature compensation value to the 24mV/C° suggested in the Firefly manual, but am a little confused about it. I think it gets entered as a negative like the -16mV/C that Victron has as default in all their presets. Also think it’s a pretty minor change, especially as my Multi does not offer adjustment. Any thoughts?

  4. Have you looked at the A&T instrument displays (aandtinstruments.com – on offshoot of Tinley)? They’re a bit niche in that they are pitched primarily as replacements for B&G Fastnet FFDs, but they have a multi protocol interface capable of N2K, Fastnet or Ethernet on the same copper (as I understand it) all configurable from your phone by bluetooth. Another interesting use of it as a config mechanism.

  5. RickG says:

    I think setting the EQ to 0V works just fine for Firefly batteries.

    Living on the dock I worried about the batteries being on float 24 hours a day. On the hook/mooring that is not a problem.

    • Ben Ellison Ben Ellison says:

      During the last three winters when Gizmo has had shore power available, I’ve been fairly careful about Float too. But now that I have the Venus system with much easier configuration access to my MultiPlus 12/2000 inverter/charger, I realized it has a Storage mode:

      “The Storage mode kicks in whenever the battery has not been subjected to discharge during 24 hours. In the Storage mode float voltage is reduced to 2,2V/cell (13,2V for 12V battery) to minimise gassing and corrosion of the
      positive plates. Once a week the voltage is raised back to the absorption level to ‘equalize’ the battery. This feature prevents stratification of the electrolyte and sulphation, a major cause of early battery failure.”

      You can see Storage in action at Gizmo’s VRM site right now:

      https://vrm.victronenergy.com/installation/30059/share/d9560ba7

  6. RickG says:

    I don’t fiddle with temperature compensation on the solar controllers. I do have temperature sensors and the BMV 712 sensor is in the warmest space.

  7. Gary Warner says:

    On another battery topic – can you make available your Balmar 614 alternator regulator settings for charging your Firefly batteries, as many of your readers with similar setups are intetested. My request some time ago for these custom settings seems to have been lost in the ether.

    Also, I have an older Victron 100/50 solar charger without the built-in Bluetooth. The accessory Bluetooth dongle works as described above and is much easier to use than the remote display accessory device for settings and firmware updates.

    • Ben Ellison Ben Ellison says:

      Hi, Gary. The “ether” you reference is my deep uncertainty about publishing settings I don’t fully understand and are to some extent specific to Gizmo’s alternator setup and the heavy loads typical when underway. HOWEVER, today I brought home all the notes accumulated as two boat power professionals helped “perfect” the settings and I promise something soon on Firefly thread. It will be qualified “use at your own risk” but maybe too will prompt expert discussion.

      • Gary Warner says:

        Hi Ben – I’d be happy to send along my settings for my Balmar 614, Victron 100/50, and battery charger, if that would be helpful.

        • Ben Ellison Ben Ellison says:

          Thanks, Gary. I would like to see your settings, either by email (ben.ellison at panbo.com) or just post them here. Note that RickG just posted Bruce Schwab Energy Systems recommendations for Balmar 614 Firefly setup (that I was not aware of), and I posted Gizmo’s more aggressive settings below.

    • RickG says:

      I use the alternator settings for the Group 31 Firefly settings recommended by Bruce Schwab. He has a PDF he sends on request that he also posted on

      File: http://www.cruisersforum.com/forums/attachment.php?attachmentid=169059&d=1525226268

      Thread: http://www.cruisersforum.com/forums/f14/how-to-properly-program-balmar-614-and-high-output-alt-162539.html

      Cheers, RickG

      • Ben Ellison Ben Ellison says:

        Hey, Rick, these are very useful links. I was hoping Bruce would do something like this PDF but the recommendations aren’t posted on his Firefly page. Thanks!

        But I’m not surprised that my 614 settings are more aggressive. They were worked out by my friend Alden Cole while we were moving Gizmo south in 2017 — and with direct Balmar consultation — and they reflect the fact that my Firefly bank is almost invariably at partial SoC when the engine is started and immediately gets constant loads of 20 plus amps when I turn all the nav electronics on:

        Gizmo’s Balmar 614 uses the default settings for AGM (AgL) batteries with these exceptions:

        bv — Bulk voltage — 14.6 v
        b1c — Bulk time — 1 hour
        Av — Absorption voltage — 14.4v
        A1c — Absorption time — 3 hours
        Fv — Float voltage — 13.6v
        FbA — Field threshold, Bulk to Absorption — 50%
        bEL — Belt Load Manager — b-2 (field reduction 14%)

        I’ve used these settings ever since and am not aware of doing any damage, but maybe I should check around again. Also, this season I will be able to see exactly what the settings do via Venus and VRM.

        • RickG says:

          Interesting. Did you up the bulk and float voltage due to measured voltage drop? Our batteries are very close to the alternator and we have 2/0 cables, so the voltage drop is very small.

          Cheers, RickG

          • Ben Ellison Ben Ellison says:

            I think that the alternator to Firefly bank run is about 8 feet and all the primary DC cables that came with Gizmo tend to oversize.

            I also have notes from late 2016 when I didn’t think that the 614 was doing its best for the Fireflies and Rod Collins advised me on about settings. They’re pretty close to what Alden and I later worked out:

            bv — Bulk voltage — 14.5 v
            b1c — Bulk time — 6 min
            Av — Absorption voltage — 14.4v
            A1c — Absorption time — 2+ hours
            Fv — Float voltage — 13.6v

            I don’t know how much Rod’s recommendations were specific to my situation or if they’ve have changed (and I’d like to), but Alden got the impression from Balmar that the 614 likes a minimum of 0.2v difference between Bulk and Absorb.

            I spoke with Alden today and he thinks I should goose bEL up to b-1 (and he had already studied my particular pulley and belt situation pretty closely).

  8. Gary Warner says:

    Hi Ben & RickG – Thanks for providing your settings for your Balmar MC-614 alternator regulators. I have attached my battery charging information package as the settings stand today.

    To put our use into context – our boat is an Ellis36 with a single 440Hp Yanmar diesel. Our house bank consists of 4-Firefly G31 batteries. Engine charging is by a Paul Grosser 180A alternator with remotely located diodes and Balmar MC-614 regulator. Solar charging is by 2x144W and 1x100W Solbian panels in parallel with a Victron 100/50 controller. Dockside charging is with a 2003 vintage Xantrex Freedom 30 charger. We have a Lifeline starting battery charged by a Sterling DC-DC charger off the house bank. No generator.

    I have modified the Balmar and Victron charging settings over time, but feel that I’m not getting the full benefit of the high capacity alternator with the 18 minute bulk time (blc) setting. I have discussed my settings with Balmar and they are reluctant to agree with a longer bulk time setting, probably for fear of overcharging. I am considering raising the bulk time setting to 30 minutes or 1 hour this season. My plan is to more closely monitor the alternator output vs time to get a better handle on bulk charging when running only the frig and when running both frig and freezer. I have tried to extend the transition from bulk to absorption by lowering the field threshold – bulk to absorption (FbA) without extending the bulk time. BTW, Balmar also informed me that the difference between the bulk and absorption voltages could be reduced to a minimum of 0.1 Volt even though they normally recommend 0.2 Volts in their literature.

    I was curious to find out other folks settings for comparison and I thank you both for proving that information. I was not aware that Bruce Schwab had provided a comprehensive recommendation for the MC-614 for the Firefly batteries. That information was not available in 2016 when I was trying to determine my initial settings. It is helpful to see his take on this issue. Ben, I can see why you have longer bulk and absorption time settings as your running load is probably at least 2 times the loads we might experience underway. Your non-running and overnight loads are likely higher as well. We also may have more solar capacity which certainly helps get back to 100% SOC on a regular basis.

    Also of interest is the information on the first page of the attachment dealing with the percent of charge that the Victron and Xantrex chargers consider a fully charged battery bank. The high Victron solar charger charging cutout level is excellent, but the lower cutout for the Xantrex charger is disappointing. I have reviewed a number of other manufacturers battery chargers and find that most cutout well below the desired 100% SOC, leaving me wondering if dockside charging without some solar capacity to top off the batteries results in diminished service life. Those boaters considering new battery chargers should check the device operating characteristics to be sure they are getting equipment that will properly charge their batteries.

    Our boat normally resides on a mooring and when cruising we anchor out or rent a mooring. We rarely dock overnight. Our largest normal loads are a 3.6 cubic foot refrigerator and 50 quart ARB freezer, both operated at 12 Volts. Overnight the house battery SOC drops to about 88-92% with only the frig running and 78-82% with both frig and freezer running.

    • Ben Ellison Ben Ellison says:

      Thanks, Gary! I just made your PDF available in a PS to the entry above.

      I’m impressed with how well you’ve documented your battery and charger system, and think it could be helpful even to boaters with different equipment. It also highlights the many — and very possibly confusing — configurations possible with a Balmar 614 regulator.

      I guess Ben Stein is impressed too, because I know he’s working on making attachments possible in comments.

  9. Ben Ellison Ben Ellison says:

    I finally got the Victron SmartSolar installed on Gizmo and of course the Bluetooth Victron Connect app was an excellent tool for instantly checking how well it was working. To my pleasant surprise, the app can now also see the Venus and thus give me another way to use the Remote Console.

    Also great is what happened at my VRM site as soon as I ran the VE Direct cable from the SmartSolar to the Venus. Check it out on the public portion of my remote monitoring:

    https://vrm.victronenergy.com/installation/30059/dashboard

    There may not be much sun in Maine today — or the rest of this week ;-( — but I can see exactly how well it’s keeping up with Gizmo’s loads.

  10. Ben Ellison Ben Ellison says:

    Very cool, especially for pro installers: The Victron Connect app can now be run remotely if the Victron device is networked with a GX / VRM system:

    https://www.victronenergy.com/…/victronconnect-v5-20-conne…/

  1. October 21, 2019

    […] Smart series can, and I don’t know of any DC/DC charger that has the powerful but easy “Smart” Victron Connect configuration and troubleshooting abilities I wrote about last […]

Join the conversation

Your email address will not be published. Required fields are marked *